Cations and Anions Tests

Testing for Cation and Anions OBJECTIVE Determine the social movement of a cation or anion by a chemical reaction Determine the cation and anion in an isolated termination All salt solutions have both positive (Cations) and prejudicious (Anions) ions interruptd in it. In this experiment you will observe chemical reactions to determine the presence of specific anions and cations. Compargon your observations with the reactions of the go to bedn solutions and the unknown solution to determine the ions present in the unknown solution. You will use a flame rill for the cations, Na+, K+, and Ca+2 Perform qualitative tests for Ca+2, NH4+, Fe+3.Qualitative tests will be used to identify anions, Cl-, SO42-, PO43-, and CO32-. Expected results of the qualitative test and the reactions argon included in your procedure. PROCEDURE Obtain from the stock room a solid unknown salt to be analyzed for the presence of both cation and anion. HC1, HNO3 atomic number 18 strong acids and NaOH is a strong base so be careful when using them. Use the plastic pipettes on the center counter to dispense your unknown solution. Approx. 20 drops is equal to 1 mL, All waste go in the waste jar labeled for your class. Bunsen Burner Safety. Make sure you are capable to get a spark out of the striker consistentlyTurn the boast needle valve counter clockwise completely. Adjust the burner barrel so your are able to see through the air inlet Check the rubber tubing and place the rubber hose on the burn out nozzle. Turn the gas jet 90 degrees. Open the gas needle valve until you hear the gas and light. If you are not successful in lighting the burner, turn the gas hit and try again. Cation Tests Al. Flame Test Label 3 test tubes, Na+, K+ and Ca+2. Bring the test tubes to the stockroom window to get your woodland splint soaked in each of the solution. You will also be given an unused wood splint to use for your unknown. Get your solid unknown as well. Soak the unused wood splint in water. Observe the change in flame color when the known solutions above are burned. K+ gives a very fleeting color change. Ca+2 gives a very similar flame color as Na+. Now that you know how observed how Na+, K+ and Ca+2, you will test your unknown. Transfer a small amount of solid unknown to a scoopula and roll the wood splint that was soaking in water in the solid unknown and burn. By the end of Part AI, you should be able to conclude the presence or absence of Na+ or K+ and maybe Ca+2. Chemical Tests A2 Because the flame test for Ca+2 is sometimes inconclusive, the oxalate test is performed. If no quick precipitation (cloudiness) is observed, heat in a water bath for 5 minutes. Water bath is set up in the southwest hood. A3 Ammonium chloride, NH4Cl, reacts with sodium hydroxide, NaOH, to form ammonia, NH3 gas. The presence of the NH3 gas is confirmed using a moistened red litmus paper place on the mouth of the test tube. Ammonia gas is basic and will turn red litmus p aper blue. A4 Fe+3, iron ion, react with potassium thiocyanate, KSCN, to form a blood red solution. By the end of Part A you should be able to identify your one cation. You must do all Tests for the known solutions. Part BThis part of the experiment test for the presence of anions, Cl-, SO42-, PO43- and CO32-. Bl Chloride ion, Cl-, reacts with silver nitrate, AgNO3 to form a precipitate that does not dissolve in HNO3. B2 Sulfate ion, SO42-, reacts with barium chloride, BaCl2, to form a precipitate that does not dissolve in HNO3. B3. Phosphate ion, PO43-, reacts with ammonium molybdate solution, (NH4)2MoO4, in acidic solution to form a yellow precipitate. A yellow solution only is a negative result. B4 Carbonate ion, CO32-, reacts with HC1 to form CO2 gas that is observed as bubbles. Part C. Each island will have a consumer product to test.